Buyer, his/her heirs, assigns, legal representatives and attorneys, knowingly and voluntarily release any and all claims,
demands, or causes of action, known or unknown, which he/she may have against the seller, his/her successors, assigns, representatives and lessees arising from any injury or illness, including death or disability, incurred in connections with the installation and use of this product.

No warranty is expressed nor implied. Buyer assumes all responsibility for the installation and maintenance of this product. Improper installation, improper maintenance, or deliberate misuse shall also release seller, his/her successors, assigns, representatives and lessees from any and all claims, demands, or causes of action, known or unknown arising from any injury or illness, including death or disability, incurred in connections with the installation and use of this product.

1) Improper installation includes, but is not limited to:
a) Failure on the part of the buyer to properly install all of the supplied parts and components in accordance with the
    supplied instructions,
b) Failure to install ALL of the supplied parts and components in accordance with the supplied instructions.
c) Modification of ANY parts or components.
2) Improper maintenance includes, but is not limited to:
a) Failure to periodically inspect installed parts and components for tightness, wear and/or damage.
b) Failure to periodically inspect and lubricate installed parts and components in accordance with the supplied
    instructions.
c) Modification of ANY parts or components.
3) Misuse includes, but is not limited to:
a) Using the installed item for purposes other than which it is intended.
b) Modification of ANY parts or components.


Several Bentup products offered do not come with instructions or complete hardware such as bolts, nuts, axles, etc…
Additional fabrication, finishing, painting, or products may be required for installation. The following is the BENTUP DISCLAIMER for all Bentup products and services provided. All bumpers, rocker skids, SAS conversions, any other Bentup product or Bentup service shall be covered by the terms of this agreement. The use of any Bentup product or Bentup service demonstrates that you have read and fully accept the terms of this agreement. If the owner of any Bentup product is unwilling to accept the responsibility and terms of this liability form, the product shall be immediately removed from the vehicle. All Bentup labor and services are performed after an agreement with the vehicle’s owner and the owner must accept the responsibility and terms of this liability form. The owner of any Bentup product or vehicle on which labor was performed which is sold, traded, or gifted must notify the new owner of these conditions and terms.


BENTUP after market suspension products and vehicle accessories modify a vehicle for uses which exceed conditions anticipated by the vehicle manufacturer. Bentup products are not designed to meet vehicular code, federal law, state law, or any other vehicle requirement. Owners accept all responsibility for verifying the use of Bentup products in their state prior to installation and use. Bentup products have been designed for the high performance demands of off-road driving, four wheeling, and rock crawling. BENTUP is not liable nor held responsible for any damages, injury’s or death that can occur from on and off-road use, the result of failure of our product’s, vehicular accidents, roll-overs, installation error, or lack of maintenance. Customer/driver assumes all liability for using a Bentup product and in assuring that the suspension system or product accessory is properly installed, maintained, and operating in safe conditions. The use of Bentup products vary in the degree of extremity and can not be controlled by the vehicle or product manufacturer. If the components within the suspension system or accessories become worn due to frequent and/or extreme off-road use, the safety and reliability of the vehicle and others is at risk. The maintenance of after market equipment to ensure the vehicle occupants safety is entirely your responsibility. Do not purchase BENTUP manufactured products or components unless you are willing to accept this responsibility. Do not install any BENTUP
products or accessories unless you feel competent at installing the product without causing present or future injury to yourself or other vehicle occupants.

BENTUP’S solid axle swap systems were designed to replace the vehicles stock suspension with a highly modified suspension system designed for off-road use only. This suspension system is not covered by any warranty by the original vehicle manufacturer or by BENTUP.

The installation of a solid axle suspension system voids the vehicle original vehicle warranty for all parts modified or parts which the modifications will have negative effects. Any vehicle with a solid axle swap will handle much differently than a stock vehicle.

Center of gravity, cornering, blind spots, braking distance, cornering, emergency maneuvers, and overall handling are all greatly modified and must be compensated by the driver. Drivers of solid axle trucks must respect the modifications and accept that their vehicle will no longer perform or handle similar to a stock vehicle. Rollovers, accidents, injuries, death, equipment failure, fabrication failure, or installation errors are possible with any highly modified suspension system including a Bentup Solid axle swap system.

The owner of any vehicle which utilizes a Bentup solid axle kit, Bentup labor to install a solid axle kit, or vehicles modified by Bentup shall accept all liability per the conditions of this agreement.

Bentup Bumper receiver hitches are not tow rated and are not designed to meet the original vehicle tow rating. Use of the hitch system provided is at the owner’s risk. Bentup bumpers are not impact rated or crash tested and will highly modify the crash ratings of the vehicle.

Any customer purchasing, receiving, or using a Bentup bumper assumes the liability and possible outcomes Bentup bumpers will have on their vehicles and other vehicles if involved in an accident. Death, injury, increased vehicular damage, increased injury to persons to the vehicle and other parties involved is increased.

Installation Instructions:

Bumpers
Test fit all bumpers before painting. Some minor modifications may be necessary to make the bumper fit perfectly, since frames can differ due to prior stress, towing, or accidents. Minor grinding and sanding may also be necessary for a perfect finish. Bumpers that are ordered for the incorrect vehicle, body lift, winch, or with accessories not noted at the time of the order may be modified by Bentup for additional charges for labor, material, and shipping. BENTUP will not accept bumpers for return that have been powder coated or sprayed with any bed liner material such as Line X or Rhino Liner. BENTUP will either refund or exchange a defective bumper that does not fit a vehicle. BENTUP will pay for shipping charges if we are the responsible party.

Solid Axle Swap Modifications
Due to the extreme modifications of a solid axle swap, we strongly recommend the suspension systems be installed by a highly experienced fabricator, off-road shop, and a certified welder. A solid axle swap kit does not come with any instructions, but phone assistance is available. There are also several websites with detailed pictures, measurements, etc… that aid in the installation.

The following are guidelines for maintaining a safe operating vehicle.
Safety and reliability are our number one concern.

1. Visually inspect all equipment for clearance and unusual wear.
2. Regularly clean and inspect equipment such as suspension components, heim joints, polyurethane bushings,
   shackles, steering, brakes, U-bolts, and all hardware. Inspect all welds for cracking. Replace items as necessary. All
   suspension components are available for individual replacement.. BENTUP reserves the right to warranty any
   components that we have determined to be product or material defective. Off-road abuse can damage suspension
   components.
3. BREAK IN PERIOD. After every installation we recommend checking the torque of all nuts and bolts to assure that
   the torque has taken. Some minor adjustments may need to be made.

Thank you for purchasing BENTUP products.

If you have any question please call AJ @ 916 207 7467.
Or send us an email at aj@bentup.com